Controller

BL-6 the well-fitting controller for small brushless outruner motors up to 6A. This new lightweight 1.8g controller for max. power of brushless motors at minimum weight can supply a constant current of 6Amp (burst 8A) to the motor! Controller characteristics and different low voltage detections for Li-Polymer and for NiMh cells can be programmed by the customer . 33,00 €/ pcs.	Technical Data:
	Safe Start with receiver signal check.
	MOS-FET RISC Microcontroller
	Nominal voltage = 6 to 13 V (2 - 3 Lipo cells)
	BEC = 5,0V, max. 0,8 A
	Motor rpm reduction for LiPo and NiMh
	Max cont. Current (A):	6 Amp
	Dimensions: (mm)	6 x 24 x 12
	Mass (w.o. wires):	1.8 g
	Mass (w. wires & connectors)	3 g !!

High-Frequency-Controller
HF100 – 0,9 gram
for a longer life of your coreless motor!

The HF100 ia a brandnew high efficiency 100 kHz self-calibrating MOS-FET µicro controller for optimized operation of coreless motors 0,9 gram, advanced high frequency DC conversion design.

New! high resolution with 256 steps from zero to full speed !!

The HF100 weighs a mere of 0,9 gram and supplies a smooth DC-voltage to your motor along the whole rpm range from idle to full speed. This high frequency controller will improve the efficiency of your coreless propulsion system by up to 15%, especially at part throttle. More importantly, the innovative design effectively eliminates the « killer » current peaks generated by normal controllers at part throttle, thereby greatly increasing the life of the commutator and brushes of your coreless motors. The throttle curve has been optimised for coreless motors and allows an extremely sensitive throttle control.

Price 64,00 Euro/ pcs.

Technology:	RISC Microcontroller with DC-DC controller, MOS-FET
Functions	Controller, BEC, safe start with “Roger” beep
Operating Voltage:	4.2 to 12 Volt
BEC:	5 V, max. 1A
Clock-Frequency:	100 kHz
Low Voltage Detection	4,2 V with precise 10bit analog/ digital conversion
Throttle Resolution	256 steps
Rpm reduction:	at < 4.8V
Current: Cont./ Max.	1,5/ 3 Amp
Dimensions (mm):	17 x 9 x 7
Mass (without wires):	0,9 g
Mass (with wires):	1,9 g

High-Frequency-Controller
HF250 – twin

this controller consists of two Highfrequency controller and has been developed especially for use in micro helicopters. One of the controller is used for the main rotor motor - the second controller on the PCB is used to control the tail rotor - both with an extremely high 256step sensitivity. With the 250kHz clock frequency they allow a long life for both - the main motor and the tail motor.

Price 96,00 Euro/ pcs.

Dimensions (mm):	17 x 16 x 7
Mass (without wires):	1,6 g
Mass (with wires):	2,7 g
Clock Frequency	250 kHz
All other technical data are the same as for the HF100 described above.

0,9 gram controller Pico 12
12 Ampére/ 10A max
from Heino Jung
Once the battery voltage is below 4V the Pico 12 switches off automatically. The integrated Auto-Programming-Modus will adjust the controller to your RC equipment automatically without any manual adjustments! The Pico 12 will be delivered with 8cm micro wires and JST micro plugs for battery and receiver connection.

Pico12.JPG (3728 Byte)

43,50 Euro/ pcs.

Technical data:

Technology: RISC Microcontroller
Current: 12Amp. contin., 15Amp. 5 sec.
6 Amp. continuous partial load
Supply voltage = 4.8 to 12 V
BEC = 5V, max. 1 A
Clock frequency = 3 kHz
Size: 5 x 14 x 16 mm
Mass: 0,9g (without wires)

Bidirectional Speed Controller
Micro 8-Bi

This microprocessor controlled bidirectional controller has been developed for use in RC-blimps and other small models. 6 to 7 cells with BEC for 2 Servos without use of BEC up to 10cells

Low Voltage detection
Continuous full power 8A, 5sec. 10A;
Clock Frequency 3kHz
Mass 1,2 g (w.o. leads); Size: 4 x 16 x 17mm

Microvor-rueck.jpg (5550 Byte)

63.00 Euro/ pcs.

Micro Gyro-System PG – 03 This Micro-Gyro-System uses a new type of piezo Sensor and is believed to be the world smallest and lightest gyro available on the market today. Yet, it has been designed to use a high quality, solid state "micro piezo" sensor, which produces the state-of-the-art gyro system. It weighs only 7.0 grams (.247 oz) including a plastic injection case, for some critical applications such as indoor slow flyers, the plastic case can be removed that makes its actual weight just 4.8 grams (.169 oz).It has been developed for use in Micro Helis, RC-Home-Flyer, blimps, vehicles .... available with Futaba/ JR connectors or with JST connectors for Helistar 53.00 Euro/ pcs.	Technical Data
	Supply Voltage	4.8 - 6 V
	Dimensions	26 x 27 x 11 mm
	Current at 4.8V	10mA
	Mass	7g/ 4,8g with/ w.o. housing